Marble Restoration & Stone Care Service

All etchings were removed from marble by polishing and buffing and then sealed. more...

The bathroom floor tiles was re honed, cleaned and sealed. Grout lines looks little darker as it’s still wet. more...

Matte or Honed finish on kitchen counter top will be turned to shine finish by refinishing technique. more...

This floor was cleaned with  stone cleaner and standard single head 17″ Mastercraft floor machine. Then sealed 2 times. more...

For all counter-tops, showers and floors it is imperative to seal the marble. It has to be noted that marble are is not as dense as granite therefore any contaminated spills are easily to absorbed. Here is the left more...

Marble bar top after restoration. It was deeply grind, polished and buffed. Erosion and roughness removed. Restaurant in Chinatown Manhattan NY. more...

Rectangular brown vanity. Polishing and re caulking. Manhattan NY more...

Before applying transparent polyester epoxy we strip old coat, fix chips and make surface matte for better adhesion. Calacatta gold marble. more...

To mount the leg we marked and drilled 5 holes with diamond drill bit. Then we fill up the holes with an epoxy and sunk the screws into epoxy. more...

This piece of antique furniture insert. Order of antique retail store in Manhattan NY. more...

This marble island was repolished by electric polisher and diamond pads such as #200, #400, #600, #800 grits and then buffed with “Dia-Glo” buffing compound, and then sealed by “Rapid Cure more...

To lift and permanently support the counter we put wooden bar between floor and counter bottom, then put some shims to completely lift it till backsplash. After the lifting we fixed the seams, cracks on sink cutout and more...

This bathroom vanity is made from the same tiles as used on walls and in shower. Good idea to save some money and match a color. Made from Rojo Alicante marble and located in Downtown Brooklyn NY. more...

We lift the vanity, fix cracks, re attach sink and re caulk the backsplash. more...

We removed the stain by just deep polishing and buffing, the stain wasn’t too deep and stayed on the top. more...

The etch was sanded down and buffed with tin oxide powder to smooth shine finish. more...

The mold roots are going on some depth into a marble pores, and often can be treated as regular stain. In some cases a tile with a mold stain can be replaced only. more...

We did re grouting and patching on most dirty grout lines, saving time and money. We call it grout repair or grout refreshing. more...

The grout was patched and refreshed by filling out missed grout lines and spreading new grout over existent. more...

The re grouting of ceramic tiles should be done with extra care, while old grout removal or scrubbing a tile can be easy chipped or scratched. Even trained worker can accidentally do so, and in most cases such chips or more...

Two marble panels were detached due to floor shifting and thermal influence of the radiator. Two marble panels attaching/re installing. more...

The terrazzo floor was ground and polished with planetary floor machine and then crystallized to shine finish with single head floor machine. The walls was polished with low speed angle polisher and buffing compound. more...

A white grout should be applied into empty and dry tile joints, removed with clean and proper tool and sponges. Otherwise a grout can be stained with dirty tool or sponge, or absorb and get stained by a dirt from more...

We cleaned up the panels, pre-wet the place and set up it back with a mortar. more...

The mold was deeply set its roots into the white grout, so it was decided to change grout and caulk instead of just cleaning. more...

The molded white grout was completely removed, new grout installed and sealed with grout sealer. more...

Image of the tiled step before cracks repair and polishing. The Fresh Store on Union Square in Manhattan NY more...

White thassos marble floor had textured/engraved ornamental line on perimeter that was removed by deep grinding and polishing. more...

This floor was decorated along the perimeter with textured tiles (tiles with rough line engraved into stone on depth about 1/4″). The owner was concerned about it getting dirty very fast, and tough to clean more...

Gloss finish was worn out by daily traffic in bathroom. Beige bathroom square floor tiles before refinishing. more...

Here are two colors of caulk was used. One on tub the second on mosaic wall corner. more...

Often the re caulking is include not just old caulk removal, but old caulk excess removal plastered on surrounding surfaces. It can be not as easy as it looks if it was spreaded on grout or on mosaic tiles. more...

The more you concentrate on maintaining the marble in a shower the immunity against moisture is increased thus saving the walls and tiles from getting stained and mold development. more...

The stains were removed with bleach penetration and then re-polished. Fortunately the stains were not absorbed too deep and successfully removed without poulticing. more...

The white caulk is the best color-matching when applying on white tub. The clear caulk can look like “shady” and darker. more...

Ceramic oval sink installed on brown limestone vanity. more...

This triangle shelf was re-grouted, re-polished and sealed. more...

Before siliconing and final mounting we finding the middle place where the sink will stay. We checking the sink cutout edges to make sure the edges are overlaying sink around evenly, also we make sure what there will more...

Before the final installing a vanity on cabinet we turning upside down the piece, pour some silicone around the sink edge, attach and tighten brackets. Then turn the slab back and remove the silicone excess. more...

Occasionally we do new sink installations or attaching it to a marble vanity. The proper installation mean the even alignment of the sink among the edges of cutout. more...

To polish the panels we used several fold-able ladders standing on scaffolding. more...

The broken parts were glued together with pre-colored knife grade epoxy and then slightly polished to shine finish. more...