Re-Grouting & Grouting
The process of re-grouting include 4 steps:
1. Remove and scrub out the old grout. For this purpose, we use a grout knife or grout saw. In some cases (for hardest lines) we use a rotary blade grinder.
2. Fill up joints with new grout. To spread a new grout diagonally across the joints, packing the grout firmly and deep into every joint we use a squeegee or rubber grout float.
3. Wipe to remove excess gout. When grout becomes firm we use the wet yellow sponges specifically designed for tile works to wipe off excess grout from the tile surface.
4. Clean tiles from the remaining residue of the grout. For this purpose, we wipe the tile surface with a dry cloth or paper towel.
Grout is concrete or sand-based material used in spaces between tiles. The main purpose of grout is to seal tile joints to protect them from moisture, to hide joints and to have a uniform appearance. We are presenting our customers with a color chart for the desired selection.
Note, to avoid scratching of shined or honed marble the non-sanded grout should be chosen.
Polyblend grout color selection card. PDF
TEC grout color selection card. PDF
Get a Free Estimete for your Re-Grouting Project:
You'll get a response within a few minutes or hours and usually not longer than 24 hours.
Before & After
Ceramic Walls above Bath-Tub (Regrouting & Recaulking)
In order to apply silicone to work surface, it is necessary to prepare it beforehand more…
Ceramic Tiled Shower Walls (After Re-grouting & Re-caulking)
All surfaces and equipment in the bathroom inevitably come into contact with water. more…
Cutting Old Grout with Hand-Held Grinder
On tough grout lines and tiles we cut the grout through with hand-held cutter, it wi more…
Ceramic Tiles on Walls Re Grouted & Re Caulked
The white grout and caulk was just applied and still soft and wet, it will need at l more…
Shower Grout Repair and Patching on Mosaic Tiles. Grout Refreshing
We did re grouting and patching on most dirty grout lines, saving time and money. We more…
Shower Grout Re-Freshing on Mosaic Tiles
The grout was patched and refreshed by filling out missed grout lines and spreading more…
1/4" Grout on Ceramic Tiles in Kitchen [Before Regrouting]
The grout was deeply soiled and owner decided instead of cleaning to change the grou more…
1/4" Grout Lines on Ceramic Kitchen Floor [New Grout]
Here is the light grout was installed. Not the best choice for the busy kitchen, but more…
Section of White Ceramic Tiles [Before Applying New Grout]
The re grouting of ceramic tiles should be done with extra care, while old grout rem more…
Shower White Ceramic Tiles (New White Grout)
A white grout should be applied into empty and dry tile joints, removed with clean a more…
Blue Tiled Countertop Old Grout Removal and Scrubbing
Blue tiled counter during old grout removal and scrubbing. It was performing with re more…
Blue Tiled Counter During and After Re Grouting.
The grout should be firmly spread over the surface and pushed into the full depth of more…
Strippin Out Old Grout from Tiled Bathroom Floor
The unsanded grout can be easy stripped out with a handheld grout saw with kobalt bl more…
Tiled Bathroom Floor with Bone Grout Color
One main component of successful grouting work is joints on a floor or walls and its more…
Similar Re-Groutings
Dirty Grout on Shower Cabin Floor
Shower Cabin Floor Re Grouted
Stained Grout on Perimeter Shower Floor
Perimeter Shower Floor Re Grouted
Porcelain Floor and Walls Regrouting
Shower Floor Walls after Regrouting
Ask Your Question or Get a Free Quote:
You'll get a response within a few minutes or hours and usually not longer than 24 hours.
